Reference list

[ Energy ] [ Pulp & Paper/PMC ] [ Oil & Gas ] [ Other Process Industries ]

	Energy
	Daimyo Industrial use of steam from waste incineration plant The waste incineration plant located in Hurum has lost its steam consumer (Hurum paper mill). Other alternatives for industrial use of the steam produced in the boiler from the waste incineration process were analyzed. Client: Daimyo AS 2009 Explosives production Production plant for explosives - phase II A cost and plan study for production plant for 500 ton/y high-energy low sensitivity explosive was completed in the phase 1 study. The phase 2 study is a downscaling to 100 ton/y, with a plan for stepwise increase to 300 ton/y production capacity. Client: Chemring Nobel AS, Sætre 2008/09 Explosives production Production plant for explosives Production plant for 500 tonnes/yr high-energy low sensitivity explosive. Cost and plan study with satisfactory uncertainty for investment decision. Client: Chemring Nobel AS, Sætre 2008 Hydro Aluminium Energy analysis of aluminum coil kiln Hydro Aluminium have several kins usedfor heat treatment of aluminium coils. This project was an analysis of the energy savings potential for one of these kilns. Client: Hydro Aluminium Rolled Products AS, Holmestrand 2008 ZENG ZENG technology qualification Technology qualification of the ZENG concept performed in cooperation with Det Norske Veritas, ZENG and Siemens Industrial Turbomachinery AB Client: ZENG AS 2008 CO2/H2O CO2/H2O Properties Research project focusing on the thermodynamic and physical properties of CO2/H2O mixtures. Financed partly by the Research Council of Norway Client: Nebb Technology 2006/08 Bio-Energy Plant BioEl Fredrikstad Engineering of Bio Energy Plant Fluidized bed incinerator wiht production of electricity, process steam and district heating (22 MW total). Engineering and coordination of Electro & Instrument. Technical responsibility for selection of steam turbine package supplier. Engineering of steam and energy distribution system. Client: BGInnovation AS 2006/07 CESAm CCS Concept Study Develop a process for increased total efficiency and increased CO2 capture for Thermal Power Plants with retrofit post-combustion CO2 capture installations. Client: The Research Council of Norway 2006/07 ZENG Oxyfuel CCS Concept Study Phase II Further development of the Concept Study Phase I for Natural Gas Power Plant with 100% CO2 sequestration. The study shall demonstrate a satisfactory cost effective solution. The object of the project is to build a demonstration plant within 2011. The concept study is financed by Lyse Energi, Gassnova, Statoil and Shell Technology Norway. Client: ZENG AS 2006/07 Patent Application Patent Application The Company has made a patent application for a process that will increase the total efficiency and increase the CO2 capture in Thermal Power Plants with retrofit post-combustion CO2 capture installations. The process is a combination of CO2 capture with amine absorption and a variant of the ZENG process. Client: Nebb Engineering / CO2 Norway 2006 Steam turbine Steam turbine cycle simulation Concept study for evaluation of profitability in new boiler/steam turbine installation. Client: Østfold Energi AS 2006 Steam turbine Steam turbine for waste incineration plant Concept study for increased power production through new steam turbine and installation of new boiler. Client: COWI AS (for Bergen Interkommunale Renholdsverk) 2006 Tine Meierier Contract and price models for steam delivery Verification of district heating system including steam delivery to nine industrial sites in Brummundal, Norway Client: Tine Meierier Øst in cooperation with Hoff Ind. 2005 Tjeldbergodden Natural gas power plant verification Study Technical verification and cost efficiency study of the Tjeldbergodden natural gas fired Combined Cycle Power Plant (CCPP) (830 MW). The objective was to give a recommendation to Haltenkraft about whether or not to become an equity partner of the Power Plant. The report also included an evaluation of the preparation for a retrofit amine absorption unit. Client: Haltenkraft DA 2005 Wood chips drying Conversion of dryer from sludge to wood chips Investigation of Andritz "Triple pass drum dryer" used for drying sludge. Evaluation and recommendations for modifications required for converting it to wood chips drying Client: Solør Tre 2005 ZENG Oxyfuel CCS Concept Study Phase I Process design of Natural Gas Power Plant with 100% CO2 sequestration. The process development was made in co-operation with CES Inc. California. Client: Lyse Energi / CO2 Norway 2004/05 Bio-Energy Plant BioEl Fredrikstad Feasibility Study for bio energy plant Preparation and pre-engineering of electro and automation system for bio-energy plant. Development and simulation of steam generation system for bio-energy plant. Client: BGInnovation AS 2004 Moelven Timber Concept Design Concept design and simulation of the process for energy production based on wet wood chips and a new gas generator process. Client: Moelven Timber AS 2004 Wind Turbine System Wind Turbine System Control of the electrotechnical system and evaluation of the concept solution. Client: Fred Olsen & Co 2001

[ Energy ] [ Pulp & Paper/PMC ] [ Oil & Gas ] [ Other Process Industries ]

	Pulp & Paper/PMC
	Voith, Düren, Germany Emergency brake system Delivery of emergency roll brake systems for two Finishing Machines. Client: Voith Paper Fabrics, Düren, Germany 2009 BCTMP factory Relocation and modification of BCTMP plant The plant is a 165 000 air dry tonnes per year mill for production of bleached CTMP from chips of Eucalyptus. The project work is basically a comprehensive revision of the technical part of an EPC contract between Pulp United (Pty) Ltd. (South Africa) and Rottneros AB for delivery of a complete bleached CTMP pulp mill for erection at Richards Bay in South Africa. Client: Pulp United (Pty) Ltd., South Africa 2008/09 Voith, Ipoh, Malaysia Relocation and upgrading of Finishing Machine Relocation and Modernization of Finishing Machine. Mechanical and electrical delivery and installation, PLC/PC based Control System with Drives for a complete Finishing Machine for Paper Machine Clothing. Client: Voith Paper Fabrics, Ipoh, Malaysia 2008/09 Albany International, Halmstad, Sweden Relocation and Modernization of a Finishing Machine. Electrical installation and commissioning of complete control system for Finishing Machine Client: Albany International, Halmstad, Sweden 2008 Voith, Högsjö, Sweden Modernization of Finishing Machine. Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Scope of supply:: - Mechanical and electrical supervision - Control system NebbOpenStep-QA, based on: - PLC system Siemens S7 - HMI system based on Citect - Servo Drives type Lenze - Fieldbus based on Profibus DP - Advanced Maintenance and Recipe system Client: Voith Paper Fabrics, Högsjö, Sweden 2008 Voith, Kunshan, China Relocation and upgrading of Finishing Machine Relocation and modernization of Finishing Machine. Mechanical and electrical delivery and installation, PLC/PC based Control System with Drives for a complete Finishing Machine for Paper Machine Clothing. Client: Voith Paper Fabrics, Kunshan, China 2008 Shri Dinesh Mills Ltd Finishing Machine Modernization of Finishing Machine. Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Scope of supply:: - Mechanical and electrical supervision - Control system NebbOpenStep-QA, based on: - PLC system Siemens S7 - HMI system based on Citect - Servo Drives type Lenze - Fieldbus based on Profibus DP - Advanced Maintenance and Recipe system. Client: Shri Dinesh Mills Ltd 2007 Voith, Högsjö, Sweden Installation of new equipment, upgrade of PLC and HMI system for Finishing Machine. Delivered systems: - Control system NebbOpenStep-QA, based on Citect. - Advanced maintenance and recipe systems Client: Voith Paper Fabrics, Högsjö, Sweden 2007 Heimbach Germany Emergency brake system - Finishing Machine Developed and delivered emergency roll brake systems for two Finishing Machines. Client: Heimbach Germany 2006 NebbPerm Installation and Commissioning Installation and commissioning of several Permeability Gauges "NebbPerm" on PMC Plants in Europe. Client: Undisclosed 2006 Voith Pater Fabrics, Høgsjø T2 Finishing Machine Installation of new equipment, upgrade of PLC and HMI system for Finishing Machine. Delivered systems: - Control system NebbOpenStep-QA, based on Citect. - Advanced maintenance and recipe systems. Client: Voith Pater Fabrics, Høgsjø 2006 Voith Porrits & Spencer India Finishing Machine Relocation and Modernization of a Finishing Machine. Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Delivered systems: - Mechanical and electrical supervision - Control system NebbOpenStep-QA, based on: - PLC system Siemens S7 - HMI system based on Citect - DC converters type Lenze - Fieldbus based on Profibus DP - Advanced Maintenance and Recipe system. Client: Voith Porrits & Spencer, India 2006 BCTMP Factory Feasibility study for new BCTMP factory Feasibility study and project leadership for a greenfield Bleached Chemi-Thermo-Mechanical Pulp (BCTMP) factory. Planned production approx. 300 000 tons/year. Client: NCT, Pietermaritzburg, South Africa 2005/07 Albany Finland (Järvenpää) Finishing Machine Rebuilding and modernization of a Kvaerner finishing machine. Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Delivered systems: - Control system NebbOpenStep-QA, based on: - PLC system Siemens S7 - HMI system based on Citect - DC converters type Lenze - Fieldbus based on Profibus DP - Advanced maintenance and recipe systems. Client: Albany Finland 2005/06 Huyck Australia Finishing Machine Rebuilding and modernization of a Kvaerner finishing machine. Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Delivered systems: - Control system NebbOpenStep-QA, based on: - PLC system Siemens S7 - HMI system based on Citect - DC converters type Lenze - Fieldbus based on Profibus DP - Advanced maintenance and recipe systems. Client: Huyck Ausralia 2005 Voith Fabrics Spain Finishing Machine Rebuilding and modernization of a Kvaerner finishing machine. Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Delivered systems: - Control system NebbOpenStep-QA, based on: - PLC system Siemens S7 - HMI system based on Citect - DC converters type Lenze - Fieldbus based on Profibus DP - Advanced maintenance and recipe systems. Client: Voith Fabrics Spain 2005 Voith Paper Fabrics, Høgsjø T6 Finishing Machine Installation of new equipment, upgrade of PLC and HMI system for Finishing Machine. Delivered systems: - Control system NebbOpenStep-QA, based on Citect. - Advanced maintenance and recipe systems. - Drives Client: Voith Paper Fabrics, Høgsjø 2005 NebbPerm Development Project Development of a new Permability Gauge ("NebbPerm") for the PMC Industry. Read more here. Client: Internal 2004/06 Bark treatment Södra Cell Tofte Bark treatment Engineering and documentation of the electrical work. Installation supervision, and commissioning. Client: Södra Cell Tofte 2004 BAT rapport Norske Skog Follum BAT report Preparation of BAT report for NSI Follum Paper Mill to meet the authorities requirement. (Based on EU-directive, IPPC) Client: Jaakko Pöyry Norge AS 2004 Green liquor Södra Cell Tofte Sludge dewatering of green liquor Engineering and documentation of the electrical work. Client: Södra Cell Tofte 2004 Mass- and Energybalance Norske Skog Follum Process study Mass- and energy balance (fibre, whitewater, SS, KOF) for NSI Follum Paper Mill. Client: Jaakko Pöyry OY 2004 Tamfelt Finland Finishing Machine Rebuilding and modernization of a Jäger finishing machine. Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Delivered systems: - Control system NebbOpenStep-QA, based on: - PLC system Siemens S7 - HMI system based on Citect - DC converters type Lenze - Fieldbus based on Profibus DP - Advanced maintenance and recipe systems. Dataexchange with SAP Client: Tamfelt Finland 2004 Voith Fabrics Blackburn England Finishing Machine Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Delivered systems: - Control system NebbOpenStep-QA, based on: - PLC system Siemens S7 - HMI system based on Citect - DC converters type Lenze - Fieldbus based on Profibus DP - Advanced maintenance and recipe systems. Client: Voith Fabrics Blackburn England 2004 Voith Fabrics China Engineering and supervision Engineering, planning, mechanical installation, test and commissioning during relocation of a Finishing Machine from USA to China. Client: Voith Fabrics Kunshan 2004 Voith Fabrics China Finishing Machine Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Delivered systems: - Control system NebbOpenStep-QA, based on: - PLC system Siemens S7 - HMI system based on Citect - DC converters type Lenze - Fieldbus based on Profibus DP - Advanced maintenance and recipe systems. Client: Voith Fabrics Kunshan 2004 Wood chipps Södra Cell Tofte Wood chipps Engineering and documentation of the electrical work. New chipper, high voltage AC motor, utility equipment. Installation supervision, and commissioning. Client: Södra Cell Tofte 2004 Bark separation Södra Cell Tofte Bark separation Engineering and documentation of electro and instrument for bark separation. Client: Södra Cell Tofte 2003 BAT report Huhtamaki Norway AS BAT report Preparation of BAT report and Mass- and energy balance (fibre, whitewater, SS, KOF) for Huhtamaki Norway AS. Client: Jaakko Pöyry Norge AS 2003 O2 mixing Södra Cell Tofte Two step O2 mixing New process in the O2 bleach plant. Documentation in Idok. Engineering, installation supervision, and commissioning. Client: Södra Cell Tofte 2003 Service PM Nordic Paper Service on the paper machine Review and service on the paper machine. Client: Nordic Paper AS 2003 Voith Fabrics Ipoh Malaysia Edge-trimming device Implementation of an automatic edge-cutting unit for cutting of fabrics. The cutter system is developed by Nebb Engineering and is also prepared for splitting of fabrics. Client: Voith Fabrics Ipoh Malaysia 2003 Boil water Södra Cell Tofte Boiler water and condensate Specification of instruments for upgrading and monitoring of boil water and condensate system. Client: Södra Cell Tofte 2002 TM2 Södra Cell Tofte Rebuilding of TM2 Engineering, Installation, commissioning and documentation (Idok). Client: Södra Cell Tofte / Jaakko Pöyry Norge 2002 Voith Fabrics Ipoh, Malaysia Automatic edgecutters including guidesystem Engineering electro and mechanical installation, supervision, test and commissioning. Client: Voith Fabrics Ipoh, Malaysia 2002 Voith Fabrics Ipoh, Malaysia Project management, engineering and commissioning. Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Delivered systems: - The control system NebbOpenStep-QA, based on: - The PLC system NebbControl (Siemens S7) - The HMI system NebbScada based on Citect - Operating station NebbOS - The information and communication system NebbCom - The maintenance system NebbMaintenance - The recipe system NebbProcessPilot - DC and frequency converteres type Lenze - Feltbus based on Profibus DP Client: Voith Fabrics Ipoh, Malaysia 2002 PM 6 Peterson Linerboard Ranheim Optimizing the regulation system for PM 6. Eveluation of the electrical system, including motordrives and regulation system for PM 6. Client: Peterson Linerboard 2001 Cristini Italy Project management, engineering and commissioning. Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Delivered systems: - The control system NebbOpenStep-QA, based on: - The PLC system NebbControl (Siemens S7) - The HMI system NebbScada based on Citect - Operating station NebbOS - The information and communication system NebbCom - The maintenance system NebbMaintenance - The recipe system NebbProcessPilot - AC motors and frequency converteres type Lenze - Feltbus based on Profibus DP Client: Kværner Eureka 2000/01 Huyck Austria Project management, engineering and commissioning. Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Delivered systems: - The control system NebbOpenStep-QA, based on: - The PLC system NebbControl (Siemens S7) - The HMI system NebbScada based on Citect - Operating station NebbOS - The information and communication system NebbCom - The maintenance system NebbMaintenance - The recipe system NebbProcessPilot - AC motors and frequency converteres type Lenze - Feltbus based on Profibus DP Client: Kværner Eureka 2000 Tamfelt Finland Project management, engineering and commissioning. Delivery of NebbOpenStep-QA ; PLC/PC based control system with drives for a complete Finishing Machine for Paper Machine Clothing. Delivered systems: - The control system NebbOpenStep-QA, based on: - The PLC system NebbControl (Siemens S7) - The HMI system NebbScada based on Citect - Operating station NebbOS - The information and communication system NebbCom - The maintenance system NebbMaintenance - The recipe system NebbProcessPilot - AC motors and frequency converteres type Lenze - Feltbus based on Profibus DP Client: Kværner Eureka 2000 Munzinger Kalander 47 Switzerland Project management, engineering and commissioning. Engineering of electrical and control system with drives for a complete Finishing Machine for Papermachine Clothing. - Information and Communication System - Servodrives - PLC - PC based HMI system - Maintenance System - Recipe System Client: Kværner Eureka 1999 Munzinger Kalander 48 Switzerland Replacement of the HMI system. Programming og commissioning of a new HMI system for a complete Finishing Machine for Paper Machine Clothing. - Information and Communication System - PC based HMI system - Maintenance System - Recipe System Client: Kværner Eureka 1999 PM6 Norske Skog Saugbrug Control System. Programming and testing of the expansion of the control system for PM6. Client: Kongsberg Simrad 1999 SND Development project DEVELOPMENT PROJECT Automation/data. Development of a maintenance system, a recipe system, a PC based HMI system, and total automation of Paper Machine Clothing (PMC) Machinery. Also development of communication over Internet/modem for maintenance and service. Client: Nebb 1999 Voith Fabrics Blackburn England Replacement of the HMI system. Programming and commissioning of a new HMI system for a Finishing Machine. - Information and Communication System - PC based HMI system - Maintenance System - Recipe System Client: Kværner Eureka 1999 Voith Fabrics Waycross GA USA Replacement of the HMI system. Programming og commissioning of a new HMI system for a complete Finishing Machine for Paper Machine Clothing. - Information and Communication System - PC based HMI system - Recipe System Client: Kværner Eureka 1999 Heimbach UK Manchester England Project management, engineering and commissioning. Engineering of electrical and control system with drives for a complete Finishing Machine for Paper Machine Clothing, including tension control in crossmachine direction. - Information and Communication System - Servodrives - PLC - PC based HMI system - Maintenance System - Recipe System Client: Kværner Eureka 1998 Ichikawa 7m Machine Japan Project management, engineering and commissioning. Engineering of electrical and control system with drives for a complete Finishing Machine for Paper Machine Clothing, including tension control in crossmachine direction. - Information and Communication System - Servodrives - PLC - PC based HMI system Client: Kværner Eureka 1998 Norske Skog Saugbrug AIM 1000 Programming and testing of expansion of AIM 1000. Client: Kongsberg Simrad 1998 Sande Paper Mill Winder Upgrade of "Jagenberg Winder" Rebuilding of "Jagenberg Winder" from pneumatic control devices to electrical control system based on Modicon Quantum PLC. Client: Sande Paper Mill 1998 Swiss Wire Ireland Project management, engineering and commissioning. Engineering of electrical and control system with drives for a complete Finishing Machine for Paper Machine Clothing, including tension control in crossmachine direction. - Information and Communication System - Servodrives - PLC - PC based HMI system - Maintenance System - Recipe System Client: Kværner Eureka 1998 Albany 13m machine Australia Project management, engineering and commissioning. Engineering of upgrading electrical and control system with drives for a Finishing Machine for Paper Machine Clothing. - Information and Communication System - DC drives - PLC - PC based HMI system Client: Kværner Eureka 1997 Huyck Italy UPS System Engineering and commissioning of UPS system for Finishing Machine. Client: Kværner Eureka 1997 Ichikawa Japan Project management, engineering and commissioning. Engineering of electrical and control system with drives for a complete Finishing Machine for Paper Machine Clothing, including tension control in crossmachine direction. - Information and Communication System - Servodrives - PLC - PC based HMI system Client: Kværner Eureka 1997 Nippon Felt Japan Project management, engineering and commissioning. Engineering of electrical and control system with drives for new press system for Finishing Machine. - Information and Communication System - PLC - HMI system Client: Kværner Eureka 1997 Paper Machine Sande Paper Mill Speed control of paper machine. Changed the control scheme and optimized the speed control of the paper machine. Client: Sande Paper Mill 1997 Voith Fabrics Canada Project management, engineering and commissioning. Engineering of electrical and control system with drives for a Finishing Machine for Paper Machine Clothing. - Information and Communication System - DC drives - PLC - PC based HMI system. Client: Kværner Eureka 1997 Voith Fabrics Högsjö Machine T2 Sweden Project management, engineering and commissioning. Engineering of upgrading a electrical and control system with drives for a Finishing Machine for Paper Machine Clothing. - Information and Communication System - Servodrives - PLC - PC based HMI system Client: Kværner Eureka 1997 Voith Fabrics Högsjö Machine T3 Sweden Project management, engineering and commissioning. Engineering of upgrading electrical and control system with drives for a Finishing Machine for Paper Machine Clothing. - Information and Communication System - Servodrives - PLC - PC based HMI system Client: Kværner Eureka 1997 Voith Fabrics Högsjö Machine T6 Sweden Project management, engineering and commissioning. Engineering of upgrading electrical and control system with drives for a Finishing Machine for Paper Machine Clothing. - Information and Communication System - Servodrives - PLC - PC based HMI system Client: Kværner Eureka 1997 Weavexx USA Training of technical personnel Course in DC drives, PLC and HMI system. Client: Kværner Eureka 1997

[ Energy ] [ Pulp & Paper/PMC ] [ Oil & Gas ] [ Other Process Industries ]

	Oil & Gas
	RLWI mk II - Riserless Well Intervention system mark II RLWI Subsea Stack Control System Engineering and development of a dynamically configurable control system for the RLWI mk II Subsea Stack. In addition to advanced stack operation and monitoring the system includes the following features: Separate SIL 2 verified Well Shutdown System, Generic Data Gateway for easier management and expansion. Client: FMC Technologies 2006/07 TTRD - Through Tubing Rotary Drilling TTRD Subsea Stack Control System Engineering and development of a dynamically configurable control system for the TTRD Subsea Stack. In addition to advanced stack operation and monitoring the system includes the following features: Riser Monitoring system, Well Information System, Valve Signature Analysis System and Remote System Management. Client: FMC Technologies 2006/07 Alvheim FPSO Hard Ware Design HW design for Safety and Automation System (SAS) Control Panels onboard Alvheim FPSO. Equipment: AIM 2000, Operator Stations and Ethernet communication etc. Client: Kongsberg Maritime 2006 Chinguetti Modification of Communication Function Changing communication logic on AIM2000 installation comunication with FMC smartmodem for subsea wells. Client: Kongsberg Maritime 2006 Frame Agreement for Standard Control Valves Frame Agreement Development Development of a frame agreement for purchase of standard control valves. The valves are mainly to be used at the Norwegian Continental Shelf. Responsible for the technical evaluation of the offers and consistency wiht the rest of Hydro's technical documentation. Client: Norsk Hydro 2006 Nakika Subsea Wells Implementing control for two new subsea wells in existing AIM 2000 installation. Client: Kongsberg Maritime 2006 Norne Extension Control System Configuration and testing of the control system AIM 2000 in connection with new subsea installations and a new communication system for the Norne field. Client: Kongsberg Maritime 2006 Oseberg Delta New field implemented of WOCS Created AIM 2000 configuration for field Oseberg Delta on workover control module. Client: Kongsberg Maritime 2006 RLWI (Raiserless Light Well Intervention), TTRD Operation and Maintenance HMI System Configuration and updating of the FMC Operation and Maintenance HMI system for subsea well systems for the following oil fields / projects: Statoil Satelite Project, Gullfaks, Snorre UPA, Vigdis, Aasgard, Heidrun. Client: FMC Kongsberg Subsea AS 2006 Aasgard B Upgrade Control System Upgrade Reconfiguration and testing of the control system AIM 2000 when upgrading the control system for Emergency and Process Shutdown (ESD/PSD) and Fire & Gas (F&G) systems at the Åsgard B Platform. Client: Kongsberg Maritime 2006 Norne Control System Configuration and testing of the control system AIM 2000 for new subsea installations at the Norne field. Client: Kongsberg Maritime 2005 Norne Upgrade Control System Upgrade Configuration and testing of the control system AIM 2000 when upgrading the control system for the subsea installations at the Norne field. Client: Kongsberg Maritime 2005 Statfjord A/B/C Control System Upgrade Creating, maintaining and running tool to upgrade from AIM1000 to AIM2000 for Statfjord A, B and C. Specification and configuration of control system upgrade for various systems which was not previously covered by AIM 1000. In addition HW design for new Control Panels. Client: Kongsberg Maritime 2004/06 FPSO White Rose Commissioning HVAC Plant Commissioning of HVAC plant onboard the FPSO Sea Rose (former White Rose) Client: AC Marine 2004 Fram Vest Control System Upgrade Upgrade of control system AIM 1000 to AIM 2000. Client: Kongsberg Maritime 2004 Kristin Control System Configuration, Design, Test and Commissioning of the Control System AIM 2000 for several equipment packages (HVAC, Gas Cleaning , Diesel System, Flare Ignition System and Glucol) for the Kristin project. And in addition VDU design and configuration of Control System to Subsea installation. Client: Kongsberg Maritime 2004 Ormen Lange Control System - Follow up Follow up detail engineering, implementation and deliveries of Control Systems for the Ormen Lange project (Condensate Export and MEG Regeneration Plant on the onshore gas terminal at Aukra). Client: Hydro Olje & Energi 2004 Rig 184 Redundant PLC Delivery, programming and documentation of redundant PLC including OP-panel for HVAC system to living quarters at drilling rig Rig 184. Client: ABB Miljø AS 2003 Rig 185 Redundant PLC Delivery, programming and documentation of redundant PLC including OP-panel for HVAC system to living quarters at drilling rig Rig 185. Client: ABB Miljø AS 2003 Ringhorne (Esso) Test and Commissioning Test and commissioning of the Power Management System, Shutdown System and Fire & Gas System for the Ringhorn platform. Programming of the process control system PlantScape, including bus-communication. Client: Honeywell 2003 Subsea Trenches Mobile Control Room Design and construction of a mobile control room. This is used for Subsea digging of trenches and deployment of sea cables in connection to an offshore windmill installation in Denmark. Client: Mika AS (Danmark) 2003 Withe Rose Redundant PLC Delivery, programming and documentation of redundant PLC including OP-panel for HVAC system to living quarters at drilling rig Withe Rose. Client: ABB Miljø AS 2003 Fram Vest Control Module Subsea installations Industrialisation of a new generation control module for operation of subsea installations. Smart development to Fram West. Client: FMC Kongsberg Subsea 2002 Gorilla VIII Redundant PLC Delivery, programming and documentation of redundant PLC including OP-panel for HVAC system to living quarters at drilling rig Gorilla VIII. Client: ABB Miljø AS 2002 Norne Control System Delivery of Subsea Control System with HMI Topside. Configuration of Soft PLC and HMI. Installation of steering electronics in instrument bottle. FAT and commissioning offshore. Client: Campus Marine / Kværner Oil & Gas 2002 Quality Assurance QA - responsible QA - responsible for FMC Houston to follow up the deliveries of several control systems to topside and Subsea installations. Client: FMC Houston 2002 Roncador FPSO Brazil Control System Design, configuration, testing and commissioning of control system for subsea wells. - HMI: InTouch - PLC: GE Fanuc Client: FMC Kongsberg Subsea 2002 Ringhorne (Esso) Control System Responsible for design, configuration and programming of VDU (HMI). Responsible for programming, configuration, testing and commissioning of Fire & Gas and shutdown(ESD, PSD) nodes. Control System based on Plantscape and FSC. Client: Honeywell 2001/03 Brasilian Petrobras Subsea Control Systems Responsible for all activities regarding engineering, fabrication, delivery, installation and commissioning of Control Systems for operation of subsea production systems on great depths. Pierce II, Roncador, Marimba, Albacora, Viola. Client: FMC Kongsberg Subsea 2001/02 GYDA platform BP Amoco Safety System Project coordinator for safety systems on the GYDA platform. The old safety systems was to be replaced during production. Coding of ESD and F&G nodes on the Honeywell FSC controller. Client: Honeywell 2001/02 Kvitebjørn (Statoil) Control System Responsible for design, configuration and programming of VDU (HMI). Control System based on Plantscape and FSC. Client: Honeywell 2001/02 Mikkel Control System System engineering and follow-up of projects on Control Systems to Subsea Installations. - Technical management - System specifications - Follow-up of detail engineering and production - Production of test and commissioning procedures - Follow-up of system tests - User documentation for Production Control System Client: FMC Kongsberg Subsea 2001 Sigyn Control System System engineering and follow-up of projects on Control Systems to Subsea Installations. - Technical management - System specifications - Follow-up of detail engineering and production - Production of test and commissioning procedures - Follow-up of system tests - User documentation for Production Control System Client: FMC Kongsberg Subsea 2001 Girassol, Angola Subsea - Engineering Subsea acoustic monitoring system for downhole sensors. Client: FMC Kongsberg Subsea 2000/01 Managerplan and control Overseeing Planning & Control Overseeing the planning and control of all the company's international projects. Implementing new tools and methods to integrate the company's resources and activities independent of geographical location. Client: Kongsberg Simrad Ocean Science 2000/01 Stena Don Fire & Gas, ESD Configuration, object and application test of node E01 (Fire & Gas, ESD) onboard Stena Don (Drilling platform). Client: Siemens Oil & Gas 2000/01 Heidrun Nordflanken Subsea - Engineering Configuration and testing of control system for subsea unit for eight wells. - Control system type AIM 1000 Client: Kongsberg Simrad 2000 R&B Drillrig Deepwater Nautilus Technical administration of Safety Systems Responsible for the completion and delivery of a safety system as part of a total integrated automation system to a drilling rig built in South Korea. The project concerned design, implementation and testing as well as installation and commissioning on site. Client: Kongsberg Simrad Safety Systems 2000 Rennesøy Baseutvikling (Rennbor) Control System Design, engineering, programming and commissioning of control system, and configuration of Lenze motors for a transportable land-based drilling rig. Client: EDM 2000 Snorre B Fire & Gas System Configuration and testing of control system for fire and gas. Simatic S7 PLC. Client: Siemens 2000 Stena Don Programming and Application Design Application design of a Fire & Gas system. Development and use of tools for automatic configuration and quality control of Siemens CFC applications. Client: Siemens Oil & Gas 2000 Mossgass Subsea - Engineering Engineering, programming, configuration and testing of control system for subsea unit for 10 wells. - Control system type AIM 1000 Client: Kongsberg Simrad 1999 Reading and Bates Safety Control System System manager on safety including engineering and configuration of control system based on AIM 1000. Client: Kongsberg Simrad 1999 Statfjord Nordflanken Gullfaks A, Aasgard A & B Subsea - System Engineering System engineering and follow up of projects within the area control systems for subsea installations. - Develop test and finishing procedures for production control systems. - Develop system sketches for electric and hydraulic power distribution. Client: Kongsberg Offshore 1999 Aasgard B Control System Upgrade Upgrade of existing control system based on AIM. Client: Kongsberg Simrad 1999 Aasgard A Work on Site Participation in testing of control system on Aasgard A. - Loop check - Image design - Configuration Client: Kongsberg Simrad 1998 Lufeng Subsea - Electro and Instrumentation Participation in project managment and manager of electro & instrumentation on Lufeng subsea. Responsible for project coordination of suppliers of umbilical, power distribution and instrumentation. Client: Kongsberg Offshore 1997 Subsea Power Distribution Subsea Development of distribution system for electric power subsea. Drives, frequency converters, electrical distribution and electrical supply for valves and electronic equipment situated on the seabed. Client: Kongsberg Offshore 1997 Aasgard B Subsea Instrumentation System engineering and follow up of deliveries to the subsea installation on Aasgard B. Client: Kongsberg Offshore 1997

[ Energy ] [ Pulp & Paper/PMC ] [ Oil & Gas ] [ Other Process Industries ]

	Other Process Industries
	Motordrives Dagblad Trykk Electrical system for a printing machine Eveluation of the electrical system, including motordrives and regulation system for printing machine. Client: Dagblad Trykk 2003 Rolling Mill Control systems and Drives Upgrading of Controlsystem and drives for rolling hoop, Emulsion system and Hot roll. Client: Hydro Aluminium 2003 Rolling Mill Controll system for cutting Al-blocks. Control- and drive system for transporting and cutting aluminium-blocks after treatment in the Hot roll. Client: Hydro Aluminium 2003 Rolling Mill Control Systems for Furnaces Upgrading the control system for monitoring and control of 4 furnaces. Including developing a redundant database system using MS SQL Server 2000 involving three servers used in production. A web based administrative report and trend system. Client: Hydro Alumunium 2003 Saab Epsilon 440, Celle 2 Control System Upgrade Upgrading of the Control system for production line. Client: Stefertec Raufoss 2003 Production line Monitoring of production line Monitoring of production line during cutting of aluminium profiles. To ensure that all profiles are cut to the right length, a line camera collects information into a mathematical model. Correct action can be taken based on the calculation. Client: Hydro Automative Structure 2002 Production line New Production Line Detail Engineering, programming, installation and commissioning of new production line. Client: Raufoss Technology 2002 Rolling Mill Production Database Production Database Planning and development of a networked database system to store production data and recipes for an aluminium rolling mill. Client: Hydro Aluminium 2002 Rolling Mill HotPass for web Developing a web based batch- and report system. Involving one server and three client systems. Client: Hydro Aluminium 2002 Saab Epsilon 440, Celle 2 Control- and regulation system Detail engineering, programming, installation and commissioning of Process Line for Steertec Raufoss to part production in the Car Industry. Client: Steertec Raufoss 2002 Nycomed Amersham, Lindesnes Control System Configuration, testing and commissioning of control system. Client: Kongsberg Simrad 2001/02 Tunnel Wireless Communiucation Study of Wireless Commucation and Transmission of data and speach in tunnels at VEAS. Client: VEAS 2001 Rolling Mill Project Management, Engineering and commissioning Project follow up, interface engineering, supervision of a new installation of electrical equipment, PLC and motordrives to a rolling mill. Client: Hydro Aluminium 2000/01 Rolling Mill Project follow up and engineering. Project follow up, engineering assistance, assembly follow up of new electrical installation, PLC and drives for Norsk Hydro rolling mill in Holmestrand. Client: Hydro Aluminium 2000 Paint Processing Engineering Project follow up, guiding and programming of expansion of enamel installation for treatment of equipment for the car industry. Client: Hydro Raufoss Automotive Plastics 1999/00 Ship CCS Cargo Control System Programming, testing and commissioning of Cargo Control System for Shuttle Tanker Project: M/T Jorunn Knutsen, Bygg Sestao 317 Project: M/T Hanne Knutsen, Bygg Sestao 318 Client: Hamworthy KSE 1999/00 Ship VOC Plant Programming and testing of process installation Programming and testing of the process installation of the VOC plant aboard M/T Navion Viking Project: Statoil, Ship M/T Navion Viking Client: Hamworthy KSE 1999/00 Process Configuration PLC based control system with HMI system based on display. Client: DtC Lenze 1999 Ship Electrical Documentation Preparation of electrical documentation for bridge systems for ships based on Elcad system. Client: Kværner Marine Automation 1999 Titania Configuration Programming, testing and commissioning of AIM 1000 upgrade. Client: Kongsberg Simrad 1999 Tanker Norway Electrical Documentation Preparation of electrical documentation for process equipment on tankers based on Elcad system. Client: Kværner Ships Equipment 1998/99 Nycomed Imaging Lindesnes Norway Configuration. Programming and testing of AIM 1000 upgrade. Client: Kongsberg Simrad 1998 Printing Office Vestfold Norway Project Management Engineering of project planning and accomplishment of all activities linked to Orkla Trykk' new printing office in Borgeskogen Stokke. Client: Orkla Trykk as 1997/98 Ichikawa Japan Training of operators and technical personnel. Course in use and maintenance of Finishing Machine. Client: Kværner Eureka 1997